Daystate Wolverine B Tuning Regulator
Reviews | Add review

Daystate Wolverine B Tuning Regulator for the 500 CC bottled versions of the Wolverine.

€ 134,95
Price per pc.

 

Fields marked with a * are mandatory
Quantity: 
Add to Cart

Huma-Air External Tuning Regulator For The Daystate Wolverine B (Bottle version)

 
This External PCP Regulator build by Huma-Air is specialy designed for  the Daystate Wolverine B with bottle.

The regulator will reduce the outgoing pressure of your rifle's pressure bottle according to your settings and this will result in a constant pelletspeed and better groups.
It is equipped with a pressure gauge what will indicate the fill pressure of the bottle and a foster male connection to fill the rifle. The position of the gauge and and foster can be chosen left or right and they can be aligned stepless into their position so it always looks good on your rifle.

When the regulator is fitted to the rifle you can read the regulator output pressure on your rifles's pressure gauge and the fill pressure will be shown on the regulator gauge.
Pressure can be set by turning the set-screw of the regulator what can be found inside the male treaded part of the regulator. A 5 minutes turn contra clockwise equals to about 6-7 bar pressure increase.
This bottle regulator will be screwed in between the pressure bottle and the action of the rifle. It will ad about 56 mm of lenght.
(your original rifle's fill connection is replaced by the regulators quick connect foster male fill connection. Do not use the original rifle bottle fill connection anymore)

 

Power setting of your rifle:

 

Please note, your rifles output power depends of the available air volume behind the regulator. The available volume in the Daystate Wolverine action is limited what also will limit the maximum power.
With our .22 Wolverine FAC set to a slightly lower power setting compared to the factory setup, we were able to almost double the shotcount to 70 shots with the regulator output of 170 bar giving us a pellet speed of 840 fps. To get these results we removed 1 coil of the hammer spring to reduce air consumption, but this can vary per rifle.



The benefits of this Huma-Air tuning regulator for your Daystate Wolverine B


  • Higher accuracy due to the elimination of the pelletspeed fluctuations
  • The solid stainless steel foster fill connection and pressure gauge can switched over from left to right
  • The position of the foster and pressure gauge can be turned around for 360 degrees. So you aligned it to your own wishes.
  • Under the pressure gauge there is a o-ring what make it posible to line the dialplate up straight for the eye. 
  • It will give you a constant pellet speed over the full working pressure range.
  • It will give you a better shotcount and a full flat shotstring immediately.
  • Adding a regulator to your airrifle will probably give you the biggest benefit in the tuning process.
  • Often the rifle will make less noise due to better balance in air usage.
 

Pressure settings of the Huma-Air regulator for the Wolverine B Airrifle
 

Your bottle regulator comes preset on the pressure we have tesed it and it is marked on the packing. You can set the regulator according to your wishes within the pressure range. The output pressure will be shown on the factory pressure gauge of your airrifle.

Our advice for choosing the best pressure range for your Huma-Air regulator:

  • Medium pressure range:  70-150 bar for all sub 12 ftlbs rifles from 1.77, .22 and .25
  • High pressure range:       100-170 bar for FAC models.



Important safety notes:


These regulators are not suitable for stand alone pressure bottles/buddy bottles.
The maximum working pressure of this model is 250 Bar.
Do not exceed the factory adviced fill pressure of your rifle.
Do not exchange the original factory bottle for a higher pressure bottle version as the Huma-Air model does not have a burst disk: When the regulator would malfunction, the full fill pressure of the bottle will be inside the action of the rifle what could be potential very dangerous.

 

 

Huma-Air Quality Control
 

Huma-Air regulators are CNC produced out of high grade aircraft Aluminum and bronze.
To guarantee a perfect product, every regulator is manually assembled, tested and adjusted to the requested pressure. 
We only use high-end materials and our belleville springs are designed for critical applications to achieve the highest repeat accuracy. This gives our regulators a repeat cycle less than 1% difference.

Add review

Thank you very much for taking the effort to review our product.

This review will not be displayed immediately, since it first needs to be approved by a moderator. Once the review has been approved, it will be displayed on this page.

All the best

Team Huma-Air

No reviews found.

More reviews